tr?id=&ev=PageView&noscript=
Blog

When to Involve a Magnet Engineer in Your Assembly Design

By Marc McClure
|
November 17, 2026
When to Involve a Magnet Engieer in Your Assembly Design | Adams Magnetic Products

Most engineers call a magnet supplier at the point they need a part number. The design is done, the housing is modeled, and the remaining question is who can supply the magnet that fits the pocket already drawn for it.

That call is useful. It is also about four decisions too late to be as useful as it could have been. By the time the pocket exists, the magnet’s size, the amount of steel around it, the air gap and the retention method are all effectively fixed, and those four things determine most of the assembly’s performance.

This is not an argument for involving a magnet engineer in every project. It is an argument for knowing which decisions are cheap to change and which are not, so you can time the conversation deliberately.

The decisions that get expensive

Package space allocated to the magnet. Available volume sets a ceiling on achievable field. If the pocket is too small for the requirement, the options are a higher energy material (which usually costs temperature capability), a different construction, or a bigger pocket. The first two are compromises. The third is a redesign.

Whether there is steel behind the magnet. A backing plate or cup redirects flux toward the working face and can improve delivered field substantially without any change in magnet material. Adding it late often means changing the housing.

The air gap. Field falls off quickly with distance, and closing a gap frequently does more for holding force than upgrading material does. Gaps get set by mechanical decisions made for non-magnetic reasons.

Retention method. Bonded, pressed, staked or fastened. Each one constrains the housing and sometimes the magnet geometry, and each has its own temperature and environmental limits. This is reversible on a napkin and painful after tooling.

Material family. Neodymium, samarium cobalt, alnico and ceramic behave differently enough that switching between them late often changes the required size, which changes the pocket, which changes the housing.

Four moments worth a conversation

1. When the requirement is written, before geometry exists

The highest-value moment. You have a functional requirement (hold this, switch that, sense this at this distance) and the packaging is still soft. A magnet engineer can tell you roughly what volume of what material family the requirement implies, which lets you allocate space correctly the first time.

2. When the operating environment is unusual

High temperature, cryogenic, strong nearby fields, corrosive media, or heavy vibration. Each of those eliminates some material options and changes the retention approach. Finding that out during environmental testing is the expensive path. High-Temperature Magnetic Assemblies covers the temperature case in depth.

3. When the design is close to a limit

If the assembly only meets its requirement at nominal conditions with nominal material, it will not meet it consistently in production. Magnet properties are published as ranges and minimums, and a design with no margin against the low end will vary lot to lot. A second opinion on margin is cheap insurance.

4. When the part has to scale

A construction that is straightforward at five pieces can be difficult at five thousand. Handling high-energy magnets during assembly, aligning them against their own attraction, and holding position consistently are all manufacturing problems that originate in design. From Prototype to Production covers what changes.

What the conversation actually involves

It is shorter than most engineers expect. The inputs are:

  • What the assembly has to do, functionally
  • The highest temperature the magnet will see in service
  • The space available
  • What the assembly mounts to, and whether that is ferrous
  • Quantity now, and quantity later if you know it

From that, we can usually tell you which material family fits, roughly what construction to plan for, and what in the current design is likely to cause trouble. If the answer is that your existing approach is fine, that is a legitimate outcome and it takes twenty minutes to establish.

No, this is not a sales call

The most common reason engineers do not make this call is that they expect a quote and a follow-up sequence. Adams Magnetic Products treats engineering support as the thing we are actually useful for, and it is available whether or not there is a purchase order behind it. We have also told plenty of engineers that they do not need an assembly, because a stock magnet and their own bracket would do the job.

Bringing a supplier in early does not commit you to that supplier. It does mean the design that eventually gets quoted is one that can be built.

Start the conversation

Talk to a Magnet Expert with your functional requirement, operating temperature and available space. That is enough for a useful first call.

If your design is already drawn, Send Us Your Drawing and we will review the magnetic side of it and tell you what we would change.

Categories:
About The Author

Marc McClure

Interested in Learning More?

Adams is ready to be a part of your products with off-the-shelf and custom applications. Contact us to find out more.

Get in Touch